2 minutes would not be near enough to jog out all of the air bubbles. Ideally, vibrating the slurry and not the mold would be best. You can rent something from a concrete tool rental company. Dunno how far you are from something. Also, in the same vein that anything is a dildo if you are brave enough, any rotary motor that spins off balance is a vibrator if its off enough.
The grain size is small enough. and you appear to be pouring upside down (thumbs up). I think all along it was only the vibration. You may have a breakout. Hard to use last pour for a volumetric comparison if the mix ratio changed. Yeah, I hope it went well.
Weighing and adjusting for temp/ph is also key. These control the chemical reaction and thus the end result.
They also make vibrators that can attach directly to a plate.
we used a custom mix that was affectionately nicknamed ‘the grog’, but it was mostly wd-40 and white lightning lithium grease.
Hi. I’m a refractory designer. I have over 30 years of experience in creating linings for industrial furnaces with bricks and monolithics, including what we would call ‘Precast shapes’ of which this would be included.
Those are definitely air pockets stemming from the pour that were not vibrated out. It could be your aggregate size is making it difficult. I don’t know the product you are using, but often there are ‘fine’ versions that feature a smaller grain size just for better consistency when pouring. I would never recommend gunning something like this.
As far as vibration goes, they sell industrial vibrators with long rubber mixing tips. I might have video from a few of my precast shapes showing a large precast shape getting vibrated. Everything about it just screams dildo and you feel silly, but it is what it is, and it does work.
You’ll know if you add too much water. It will be brittle and fail if you can even get the mold released. More water is never a solution. Better PH is superior to more water.
Vibration can be achieved by building an outer box for your foam insert. Wood can work for something this size probably, but metal would be best. You can then use any vibratory method that works. Pour direction matters too, but it opens ugly doors like lifting and drying.
I own ‘Fear & Hunger’, the game pictured atop the article. I play it. I enjoy it. I have nothing to give but accolades for this game. The author was brilliant in the game design and story. Their target audience is a mature adult. The video game plays as a turn based top down survival horror rpg. It’s a very minimalistic game in it’s world, though it has a lot of unique gameplay programming that elevates it’s style above others. The story though… Wow.
You are simply going to the bottom of the dungeon to kill someone and then leave. That’s it. However, It does have very adult oriented… things… peppered into the game. The setting is pretty dreadful, and as you proceed it only gets worse. Eventually, when you think it’s hit rock bottom, it finds a brand new shovel. It hits pretty hard too.
If you are an adult that can handle adult and survival horror themes, it’s well worth a play and you should buy it immediately. It’s a lot of fun, though get you feet set. The game will shock you out of your comfy place, and it will do so multiple times. Not my favorite horror game, but probably in my top 5. Brilliant and violent, both to the extreme.
Additionally, all of these adult themes need their own filterable genre tags so that they can be included or excluded when you browse by filters.
Wow. My furnace just kicked on. Isn’t that the digital inverse of Stockholm Syndrome?
As a professional 35 year draftsman, I would recommend you buy an 11x17 gridded notepad, a pencil, an eraser, and then make numerous sketches. Do an plan view of each floor to create the general arrangement and the room-to-room relationships. Sections will be required at each elevation to show heights. Then sketch each room on its own sheet. Here you can supply more detail, using matchlines, etc. In this manner, you don’t have to bear the burden of drafting and accuracy until you are behind the screen. You can just sketch the idea, and provide the numerics. Sketches need not be pretty or to scale or made by someone with any drafting talent at all. Use placeholders. A square with ‘TLT’ in it is just fine for a toilet. Later, the sketches can be redrawn in cad via a scaled floorplan and your placeholders detailed as required. This is generally how I would proceed when I had to draw up large steel furnaces in which the OEM drawings were lost.
With that in mind, Id suggest paying cash to someone else that has cad software and knows it. This is not a large or even complex project. They can take your sketches and recreate them into a 2d drawing set assuming you did your sketches right. While it will be a great accuracy check, I recommend this just so you don’t have to run CAD on Linux, an endeavor that is sure to cost you that cash in time and frustration alone. It’s just not suited for the heavy throughputs of CAD.
Consider this. If your choice of tools does not matter, you could replace your screwdriver with a butter knife for this renovation. As well you could use a rock in place of a hammer or some eco-friendly hemp string in lieu of your tape measure. If the choice of operating system, the base for all software to run on, is a negligible detail you may as well remove your foundation while you are at it. It’s just going to crack and leak in 200 years or so.
If you don’t know any starving draftsman or doing it yourself is an additional goal, then at least go buy a cheapie beater windows laptop and get a mainstream cad software, even if it’s free. You’ll be needing something mainstream to get good search results as you learn to run it.
And please, if this comes off as rude, I assure you that it’s borne from my first hand experience. CAD drafting is not difficult, but it is tricky. There will be many moments where things can get off the tracks without you realizing it. It’s disheartening to say the least when you realize that many minutes, hours or days ago you punched a bad number, misread something, phone rang and you got distracted, etc. And then when that happens, you have to know how to fix it since some of the drawing is right and some is now wrong, and a wrong drawing isn’t necessarily worth the paper it’s printed on. A good cad guy will avoid most of these traps for you entirely.
I happen to be working in a major grocery store right now that draws from UNFI for 75% of our product. Our shelves are far from bare, but our deliveries have been affected. Certainly, stock quantities are only going down. I did not receive any stock Monday. I was told they took our order from a prior Wednesday and resubmitted it for delivery this Wednesday, but it did not arrive. An order is in place for tomorrow, but again, we didn’t shoot it so they must be using sales estimates or another prior order. I hope it shows up, but its not likely I’ll be getting it (a truck is scheduled but with no eta).
We have other suppliers and are drawing additional items from them where we can, but they cannot quell the full demand in either quantity or diversity.
I’m surprised they had no backup system in place. That was incredibly unwise and irresponsible considering it is food chain related. Funny how banks are too big to fail, but not food suppliers.
That condition is a despotic red-flag deal-breaker that should be countered with epic abandonment. Let them know this is not OK. If I hadn’t uninstalled it years ago, I would have already. Lots of better browsers out there.
HP was great in the 90’s. They made quality stuff back then. My HP4MV’s were like a tank. They built a great name for themselves legitimately. That all changed in 2000 when that dingbat took over as CEO. Everything they made became ultra cheap. When I’m out shopping, I’ve been known to approach random strangers that I observe looking to buy a printer just to tell them how bad HP is.
I personally stopped using them in 2002 after a brand new HP-5610 multifunction doc center cockblocked itself from windows 98 because I plugged in the usb data cable that connects the computer and printer without installing their bloaty software FIRST. It was a long night reinstalling the OS I had just reinstalled the week prior. Their helpdesk was so infuriatingly dumb and unhelpful I made it a goal to steer anyone away from them that I can.
The Brother laserjet I purchased as a replacement in 2007-ish is still going strong as well. I’ve never even serviced it (other than replacing toner and paper). Admittedly, it’s getting tired after 18 years.
You do not need to support a company that treats its customers as badly as HP does, and never support anyone or anything that thinks you deserve to stand there like an idiot for 15 minutes before they can do their job for you. That, kids, is called neglectful and disrespectful.
7th Saga. It’s a turn based top down RPG (similar to Final Fantasy 1 or Dragon Warrior 1). The games AI sometimes just kills you (and takes great delight in it). Easily the most frustrating RPG I’ve played.
Blaster Master for the Nintendo (NES) as well. Instead of evil AI you get evil level design that wants to kill you.
Now if you’ll excuse me, I’m off to have a sandwich and play some Leisure Suit Larry 3.
You may want to opt out of those services. Even LinkedIn seems to know it’s got potential to be a flaming hot train wreck, apparently to the point where they desire no responsibility for the public messages made by their machine that they own, train, and qc.
Ahh, I was mistaken. Libre is open source.
Having used autocad for nearly 40 years, I will say they stick it to their customers pretty fiercely. I still use 2010 with 3rd party software to get it to run on win10 at home. I do a lot of solid models and assemblies as well as technical 2D drawings and renderings.
FreeCAD is impressive, but it lacks an easy to use interface. NanoCAD and LibreCAD are not open source but are free and are both better 2D alternatives.
Edit: LibreCAD is open source.
They trip all over themselves just to seemingly not use the phrase “open source” huh?
I built a PC for my little sister in 2007. She was starting college and didn’t have a computer. It totaled 2805 and some change, custom built through Antares Digital (When you know, you Lili). These were all top of the line components (Asus M2N32-WS PRO, Amd athlon64 X2 AM2 5200, Corsair Memory). Not a cheapy system in its day.
Three nights before I was to deliver it to her, I completed all of the setup, had all the software ready to go, even setting up a custom theme for her (We were both metalheads). My folks said that she would need a printer/fax/copy/scanner as well, so last minute, I ended up buying an HP 5610 at target for 192 dollars.
The HP instructions didn’t say that if you connected the cable between the printer and the PC before you had installed the drivers, the printer would not mount as a device. In fact, it would never connect to that PC ever again. Apparently, it ruined the registry until you reformatted and reinstalled the OS.
To be fair, the manual did say to install the drivers first, then the cable, but this was not the norm back then and they didn’t really emphasize it in any way, nor did it mention that you were about to be FITA big time. Had to scramble to completely reformat the drive, reinstall all the software… Essentially, starting over from a blank slate and getting done in 2 days for delivery to her dorm on move in day. It did connect second time around.
I wrote them an angry letter regarding the poor deployment, but of course I never heard back from them. Never bought another HP for myself or anyone else ever again. I go out of my way to encourage people to not buy anything from HP. If I happen to be somewhere and see someone looking at an HP printer, I’ll just approach them, introduce myself, and tell them my story to discourage them from buying it.
CDs are still king with me. 1,957 and still counting. I feel cheated if I don’t get to enjoy that romance of flipping through the liner notes while listening to the CD that first time. I rip the songs I like after a few days of listening to it. I suspect the day will come when MP3’s will not be free.
DVD’s too. Almost 1,400 of them as well.
I did have to let the cassette tapes go. I kept some of the rarer ones, but they weren’t meant to last 40 years and would not likely survive another rewind.
Just inadequate vibration. Really take your time with it. What’s your set time?